Posted on 2 Comments

How Do You Finish your Wood?

The two questions I am most often asked when I am at a show and people look at my items are, “How do you finish your wood?” or “What do you use to finish your wood?” They usually ask about my pens.

Over time I have used several types of finish and experimented with a few others, but I have settled on a specific type.

Before any finishing product hits the wood…

The finishing process begins way before any drop of liquid comes into contact with the wood. I don’t remember where I heard this but the words ring true in my head anytime I am working with a piece of wood.

Your finish only looks as good as your sanding

This makes a huge impact on how your finished piece turns out visually. If your wood is roughly sanded, and there are sand lines through the wood, no amount of finish is going to make that look good.

I sand at a slow speed with the lathe running around 500 rpm’s. This allows no heat to build up and to not have the sandpaper load. Generally I start out with a 220 grit paper and work my way up to 1200 grit sandpaper. This gives the wood a soft silky feel. Also between grits I reverse the lathe and sand with the grain to remove and sanding lines.

Once I am done sanding, I use a soft cloth I to wipe the wood down with Denatured Alcohol (DA) to remove any dust prior to applying the finish. DA cleans the woods and dries quickly without penetrating the wood like water can.

My homemade sandpaper dispenser
My homemade sandpaper dispenser

What about wood stains?

Wood stain is something I don’t use right now. As I tend to work with either exotic or reclaimed/recycled wood I want the natural grain and beauty of the wood to come through. Wood stains can mask that.

Exotic woods like Bocote, Cocobolo, Olivewood, etc. have their own beauty which would be a shame to hide behind a wood stain. My personal opinion is not to hide what nature created.

As for the reclaimed and recycled wood, when I begin turning it, it’s like unwrapping a present. You never know what you are going to find inside until you start peeling back the layers. I have begun turning what looked to be a bland piece of wood but once I began I uncovered hidden inclusions, wood knots, and some gorgeous grain patterns.

When working with wood, it’s like uncovering hidden treasure.

When it’s time to finish the wood…

As I said before I have played around with several types of finishes especially with my pens. From Friction polish, which is commonly a combination of Shellac, Denatured Alcohol, and Boiled Linseed oil, to various paste wax finishes and even Walnut Oil finish. While they are nice, they weren’t quite what I wanted as a finish especially with the pens.

The finish I ended up using and sticking with for my pens is Cyanoacrylate glue which is more commonly known as Super Glue. It creates a hard and durable coating that allows the beauty of the wood to come through while giving it a high gloss shine.

Even with this I have tried several different types and my CA of choice is Titebond. This brand has a good working time, dries fairly quickly, and holds up well.

There are two types of CA finish that can go onto the pens. I start out with five coats of thin CA. This soaks into the wood, and as the name implies, it is very thin and has incredible wicking properties. This comes in handy with woods like Zebrawood or Paduak which are naturally open grained and can have small natural voids in the wood that need to be filled.

Once the thin CA is applied, then I move on to Medium CA, which I apply about ten coats of. It builds a hard shell around the pen barrel which not only looks good but creates a protective barrier. Once this is fully dried and hardened, no matter how much you handle your pen, take it in or out of a purse the shine will always be there.

Titebond CA glue for finish or as it is more commonly known as Super Glue
Titebond CA glue for finish or as it is more commonly known as Super Glue

Hands off!

For a while I had a love/hate relationship with CA finish and it frustrated me to no end.

On occasion I would get a what looked to be smoky spots appearing on the blank when I would start polishing them. In order to figure out what was going on I did several things.

  • I bought fresh CA thinking it had gone bad.
  • I tried it with and without accelerator (which cures the CA faster).
  • Thinking it had something to do with the Florida heat and humidity, I tried playing around with applying it at different times of the day.

In the end I was fingered as the culprit.

Between each coat of CA you have to let it dry completely before going on to the next. I touched it with my finger to test the dryness. If it hadn’t dried enough, I would feel the tackiness on my finger.

What I didn’t realize was that when I did this it was also transferring oils from my skin to the finish which would then appear as a smoky spot when I started wet polishing.

So now between coats my new mantra is, “Hands off!”

An example of the smoky spots I would find in the finish from time to time.
An example of the smoky spots I would find in the finish from time to time.

Time to polish and buff…

Once the coats of CA are finished, and it has dried, there are still two more steps before I’m done.

First there is the wet sanding/polishing. For this I use pads called Micro Mesh. They run from 1500 grit up to 12,000 grit.

When the CA dries, it is not always smooth or even. The Micro Mesh pads takes care of that. I soak the pads in water as they have a sponge-like quality. With the lathe running at 500-600 rpm’s I wet-sand the blanks. The trick with these is to keep them wet and not to let the pads dry out.

As you polish with them, a slurry forms. Between each grit, wipe off the slurry with a soft paper towel.

Once I have gone through all the grits with the Micro Mesh, then the blanks come off the lathe and are ready for the buffing wheel. The wheels I use are cotton, and one is coated with Tripoli powder. With the lathe running at about 2700 rpm’s, I buff out the blank on the wheel with the Tripoli powder. Once that’s done, then I move on to the clean cotton wheel.

When it’s done, the blank pops and shines, and it’s then ready to assemble.


While this process may seem time consuming, it’s well worth the end results. It produces a pen with a luxurious finish that will last a lifetime.

Here are a few examples of my pens done with a CA finish.

2 thoughts on “How Do You Finish your Wood?

  1. My god, your work is absolutely GORGEOUS! You can feel the care and attention lavished on these during every part of the process, even if you hadn’t described the process in depth. I’m completely with you on preferring to keep the natural grain and color of the wood as the focal point, so the fountain pens in particular are causing some envious drooling on my part. You wouldn’t happen to sell online, would you?

    1. Hello and thank you. I do sell online and you can find my most up to date listings here. Just click on the banner at the top of the page and it will take you to the shop.

      Since I started wood turning I have found that each piece of wood has hidden beauty underneath. The texture, the grain, the color; to hide that with stain would detract from that.

      Again, thank you for stopping by.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.